Akcija!
,

3D TOUCH Auto BED Leveling Sensor V3.2

Turime sandėlyje

  • Tinka daugeliui 3D spausdintuvų
  • Komplekte prailginimo laidas
  • Supakuota kompaktiškoje dėžutėje
Prieinamumas

Išparduota

24.99 38.99

Išparduota

Gauti pranešimą el. Paštu kai prekė pasieks sandėlį.

Skirtas sukalibruoti 3D spausdintuvo pagrindą (bed).

Features

1 Simple

3DTouch can be easily applied, since it has a small and simple structure. Gathering information & firmware setting will be an easy task, because 3DTouch works as usual auto bed leveling sensor.

2 Smart

Self-test: The push pin is operated two times to test when the power is on

Alarm: The LED light blinks if a problem found on a self-test or on an operation

3 High-precision 

3DTouch’s Standard Deviation in repeatability is around 0.01mm, at that precise.

If you choose 3DTouch, your 3D printer will be high-class masterpiece, giving you an enjoyable experience.

4. Innovative Solenoid: Ultra Power Saving

On idle state, while the push-pin is whether pulled out or retracted, there are not any electric current flowing on solenoid, and standby electric current in the whole device is below 15mA on average, whereas on working state, while the pin is moving in sudden about 100ms, under 300mA flows in the device.

Low power consumption even further drops joule heating, preventing from heat problem.

5 Technologies 

3DTouch consists of Atmel ATtiny13A, solenoid, and a push pin.

6 wide Selection of Bed

3DTouch does not uses either optical, nor proximity (inductive/capacitive) sensor.

3DTouch is controlled by Hall Effect, providing high precision. Thus the bed material can be selected freely.

7 Optimized structure:  Larger Build Size

3DTouch is a small and technology-intensive one. Build size can be set larger than other existing auto bed leveling sensor.

3DTouch uses existing RC Servo motor signal intactly, so just plug 3DTouch on the same pins after removing servo motor.

Specifications

Voltage: 5V

Current: 15mA

Max. Current: 300mA

Cable length: 150mm

Net Weight: 10g

Shipping weight: 25g

Wiring

3-pin: Brown (-, GND), Red (+5V), Orange (control signal)

2-pin: Black (-, GND), White (Z min)

Package List

1 X 3DTouch Auto leveling sensor

1 X 3Pin Straight Pin

1 X 2Pin Straight Pin

2 X Screw & Nut & Washer

2 X Dupont Housing Shell 3Pin

2 X Dupont Housing Shell 2Pin

3 X Dupont Housing Shell 1Pin

14 X Dupont Terminal

1 X 10KΩ 1/8W Resistor

Operate Condition

3DTouch can be operated in the following condition.

One I/O for control (PWM or Software PWM)

One I/O for Z min (Z Probe)

GND and +5V power

 

3D TOUCH V3.2 version

 

Description:
3D Touch V3.2 is the new generation hotbed automatic leveling accessory of FDM 3D printer. Built by the latest technology, it can accurately measure the inclination of the hotbed. It can be used for hotbeds made of glass, wood, metal, etc. Users no longer need to manually level the hotbed, bringing users a simpler and faster hot bed leveling experience, and improving the printing success rate and printing accuracy.
Equipped with new structural design for higher precision, 3D Touch V3.2 can be widely used in various FDM 3D printers, it is a necessary accessory for 3D printers;
Feature:
New structural design, higher precision
High precision, accuracy deviation is 0.005mm
Suitable for various materials hotbeds
Automatic detection after power on
Abnormal alarm
More stable and reliable
Intelligent measurement
Specification:
Voltage: 4.8~5.1V
Current: 15mA~300mA
Packing list:
1. 3D-touch: x1
2. M3 screw: x4
3. M3 nut: x2
4. Metal holder: x1
5. 18cm cable: x1
6. 100cm cable: x1

 

 

Produkto kodas: TRE181519 Kategorijos: , Žymos: , ,

Based on 0 reviews

0.0 įvertinimas
0
0
0
0
0

Parašyk atsiliepimą pirmas “3D TOUCH Auto BED Leveling Sensor V3.2”

Nera atsiliepimų

KREPŠELIS

close